micro asphalt specification

Microsurfacing specs deserve a weather variable | Asphalt ...

Increasingly, microsurfacing is one of the preservation tools used by state agencies to extend the life of asphalt pavement. However, the current microsurfacing specifications in U.S. do not seem to differentiate between the various climate conditions encountered …

Micro-Surfacing | Emery Asphalt

Micro-Surfacing includes polymer modified asphalt (key in flexibility), aggregate, mineral filler, additives and water. Micro’s effectively seal, level, rejuvenate, and …

Contact Us · Fog Seal

Micro Surfacing Company Asphalt Microsurfacing Pavement

Micro surfacing is a polymer modified cold-mix paving system that can remedy a broad range of problems on today’s streets, highways, and airfields.  Like its sister product,  slurry seal, micro surfacing begins as a mixture of dense-graded aggregate, asphalt emulsion, water, and mineral fillers.

MICRO SURFACING AME AASHTO T176

Jan 01, 2019 · Micro Surfacing is a mixture of a latex-modified asphalt emulsion, crushed mineral aggregate screenings, mineral filler, water and other additives for control of set time in the field. No limestone aggregate will be permitted in the mixture.

Microsurfacing Treatment Types

Microsurfacing is similar to slurry seal. It consists of the application of a mixture of water, asphalt emulsion, aggregate (very small crushed rock), and chemical additives to an existing asphalt pavement surface. Polymer is commonly added to the asphalt emulsion …

Micro Surfacing - International Slurry Surfacing Association

Micro Surfacing creates a new, stable surface that is resistant to rutting and shoving in summer and to cracking in winter. Applied to both asphalt and Portland cement surfaces (usually preceded by a tack coat on ), Micro Surfacing is often used to restore a skid-resistant surface to slick bridge decking with minimum added dead weight.

MICRO-SURFACING

Micro-Surfacing application is plastic deformation or pushed up asphalt on the surface. Here is an example where the surface lift has pushed up at the edge line. Once again the Micro-Surfacing material does a good job of filling in any low spots in the surface but it is not very effective when used to correct high areas in the road.

Pavement preservation is cost effective with micro-surfacing

Learn why micro-surfacing is the smart asphalt maintenance solution with cape seals, slurry seals, and crack & joint sealing.

Micro-Surfacing Contractors - The Midwest's micro ...

Why Micro-surfacing Used at the right time, micro-surfacing is an effective, cost-saving form of pavement preservation that is being used on an increasing basis. Cape Seals

Road Standards and Paving Standards

ASTM standards designed to ensure quality road, paving, and related transportation materials.

Supplemental Specifications

Note: All files are presented in a PDF Format. 2007 Supplemental Specifications

INDOT: Standards & Specifications

INDOT Doing Business with INDOT Consultants/Pre-Construction Current: Standards & Specifications ...

Specifications

Travelers. 511 (Real-Time Traffic Info) Alternative Intersections. Displaced Left Turn (DLT) Intersection; Diverging Diamond Interchange (DDI) Reduced Conflict U-Turn (RCUT) Intersection

Developmental Specifications

Developmental Specifications . Developmental Specifications are specifications developed around a new process, procedure, or material approved for limited use by the State Program Management Office. These specifications are signed and sealed by the professional engineer responsible for authorizing their use and monitoring their performance in the field.

rsta-uk

è Slurry surfaces and micro-surfaces. can be specified in accordance with the specification for highway works clause 918 è These materials are recognised. as products regulated by the Construction …

Publications - Standard Specifications for Road, Bridge ...

Sep 01, 2019 · The Standard Specifications have been developed to serve as a baseline for the work that is delivered to the public by the Washington State Department of Transportation.

changed p4 font copy A-143 Final January 2001

Micro-Surfacing is a mixture of polymer-modified asphalt emulsion, mineral aggregate, mineral filler, water, and other additives, properly proportioned, mixed and spread on a paved surface in accordance with a specification and as directed by the Buyers Authorized Representative (B.A.R.).

How Micromilling is Saving States Money on Asphalt Road ...

Nov 30, 2011 · It can be done on both asphalt and roads, so it is a versatile technique. Contractors, however, may find that micromilling drums are considerably more expensive than conventional drums ...

2016 ROAD AND BRIDGE SPECIFICATIONS

Updated: 2016 ROAD and BRIDGE SPECIFICATIONSMARCH 2020 — (Division III) — Saved: 02/21/2020 1:30 PM TOC , VDOT Web , OVDOT , I , II , III , IV , V , VI , VII ...

DIVISION II CONSTRUCTION AND MATERIAL …

American Public Works Association 1 February 2017 Kansas City Metropolitan Chapter . SECTION 2201 SUBGRADE PREPARATION 2201.1 Scope This section governs the furnishing of all labor, materials and equipment for the preparation of subgrade as shown on the

CONSTRUCTION SPECIFICATION FOR MICRO-SURFACING

When the Contract Documents indicate that municipal -oriented specifications are to be used and there is a municipal-oriented specification of the same number as those listed below, references within this

Efforts to Improve Micro Surfacing Performance

The 2016 Standard Specification Book contains two (2) options for micro surfacing emulsions based on the above projects successes. The first is the standard harder based asphalt emulsion (PG64-22).

Kentucky Standard Specifications | KYTC

Home; News/Media. District Pages; Newsroom; Office of Public Affairs; Snow/Ice Information - SnowKY.ky.gov; Road Conditions - GoKY.ky.gov; Maps/Resources. Maps

Item 340 Dense-Graded Hot-Mix Asphalt (Small Quantity)

This specification is intended for small quantity (SQ) HMA projects, typically under 5,000 tons total production. ... and Micro-Deval tests. Perform all other aggregate quality tests listed in Table 1. Document all test results on ... Warm Mix Asphalt (WMA) is …

Table of Contents

05-299 (7-08) PUBLICATION: TRANSMITIAL LETIER Publication 242 ~ May 2015 Edition pennsylvania DATE: DE PARTMENT OF TRANSPORTATION January 14, 2016 SUBJECT: Change No. 1 …

Item 341 Dense-Graded Hot-Mix Asphalt

Warm Mix Asphalt (WMA) is defined as HMA that is produced within a target temperature discharge range of 215°F and 275°F using approved WMA additives or processes from the Department’s MPL.

“MICRO-MILLING” The Finer Side of Milling meets …

Micro milling represents an attractive alternative to conventional milling under the right circumstances, and is a fresh approach to surface preparation and increasingly surface preservation.

STAR SEAL | SEALCOATING PRODUCTS

Star Seal's MICRO-PAVE® asphalt emulsion sealers are a heavy-duty sealcoating that is specially designed to protect and beautify asphalt pavements. e.g. airports, commercial parking lots, home driveways, etc. STAR SPECTRUM® Brilliant Acrylic Specialty Coating

Micromilling Treatment Types

What? Micro-milling is the removal of a small thickness (1 inch or less) of existing asphalt prior to placing a surface treatment. The difference between cold milling and micro-milling is the texture left on the existing pavement.

Recommended Performance Guideline - The Barnhardt …

Micro surfacing is a quick-traffic system that allows traffic to return shortly after placement. Normally, these systems are required to accept straight, rolling traffic on a 0.5 in (12.7 mm) thick surface within

CONSTRUCTION SPECIFICATION FOR MICRO-SURFACING

This specification covers the requirements for micro- surfacing and includes all surface preparation, material application, tack coating, handwork, joints, protection while curing, clean up, and trial area. 336.01.01 Specification Significance and Use . This specification …

“MICRO-MILLING” The Finer Side of Milling meets …

asphalt pavements. Micro-milling uses a milling drum with more teeth and a tighter lacing pattern to create a smoother surface than the traditional milling process.

Macropaver - Slurry & Polymer modified Micro Surfacing …

Macropaver is known for its flexibility, rugged & reliable, high production, low-cost performance, 60 years in pavement & road maintenance industry

Table of Contents

specification of 65 gyration asphalt mix designs will not be allowed on projects let after December 30, 2016. The only acceptable asphalt mix designs will be 50 gyrations ( < 0.3 million ESALs), 75 gyrations (0.3 to < 3.0 million ESALs), and 100 gyrations (3.0 to >30.0 million ESALs) mix designs.

Specifications and Details for Public Works Construction

FOREWORD. Publication of these Uniform Standard Specifications and Details for Public Works Construction fulfills the goal of a group of agencies who joined forces in …

Standard Specifications for Road &amp; Bridge Construction

The Standard Specifications for Road and Bridge Construction contain requirements setting out or relating to the method or manner of performing work or to the quantities and qualities of materials and labor for all FDOT contracts. You will find links to the standard specifications documents...

Construction Specifications

Construction Specifications Publication 408. The construction specifications for PennDOT projects, outlined in PUB 408, are available electronically on the Forms, Pubs & Maps section of the website.. Standard Special Provisions. Standard special provisions are maintained electronically in ECMS; PennDOT does not maintain a hardcopy format.

STANDARD SPECIFICATIONS FOR HIGHWAY …

Section 2 Specification 2.1 Clearing DECEMBER 2010 1 2.1 CLEARING 2.1.1 GENERAL 2.1.1.1 Description Clearing shall consist of cutting, piling, removing and disposing of trees, brush, stumps, logs and roots from areas shown on the Drawings or as designated by the Consultant. 2.1.1.2 Clearing in Forest Protection Areas

Micro Surfacing Quality Construction

micro surfacing, the residual asphalt content must be between 6.5-8.5% and mineral filler must be from 0.26- 3%.

30 Years of Microsurfacing: A Review

Microsurfacing is a road maintenance tool that involves laying a mixture of dense-graded aggregate, asphalt emulsion (about 7% by weight), water, polymer additive (about 3% by weight), and mineral fillers (about 1% of weight of total dry mix) to correct or prevent certain deficiencies in pavement conditions [ 1 ].

SECTION 401 ¾ ASPHALT PLANT REQUIREMENTS

in each storage tank or in the asphalt binder feed lines connecting the plant storage tanks to the asphalt plant. When the sampling valve is located in the feed

SPECIFICATIONS

Pub 408/2003 is a single set of Construction Specifications that contains all measurements in dual values, Metric followed by English in parentheses. This feature was used to facilitate the construction of individual projects using

dot.ga.gov

dot.ga.gov

CONSTRUCTION SPECIFICATION FOR MICRO-SURFACING

When the Contract Documents indicate that provincial-oriented specifications are to be used and there is a provincial-oriented specification of the same number as those listed below, references within this

PAVEMENT SPECIFICATION CHANGES

MICRO-SURFACING AND SLURRY SEAL • Cold applied mixture of polymer modified asphalt emulsion (CSS-1hPM), high quality aggregate, mineral filler, water, and additives • Can apply in variable thick cross-sections: wedges, ruts, scratch courses or final riding surfaces • Good skid-resistant surface (high wet friction coefficient)

KDOT: 2015 Standard Specifications for State Road and ...

hma base (reflective crack interlayer (rci)) 15-06009-r01 - hma base (reflective crack interlaer (rci)): 615: saw and seal joints (hma overlay) 15-er-1-r19 - errata sheet for standard specification book for state road and bridge construction, edition 2015: 15-06001 - plant mix asphalt construction (bm-mixes): 15-06002 - plant mix asphalt construction - commercial grade (bm-mixes)

pages - Asphalt Information

The Asphalt Materials section of the Office of Materials Management conducts testing and personnel approvals in support of ODOT Districts project contract administration, contractor and supplier approvals, material investigations, as well as implementation of new specifications and technology.

Technical Advisory T 5040.36 Surface Texture for Asphalt ...

Jun 17, 2005 · Microtexture is generally provided in asphalt pavements by the relative roughness of the aggregate particles and in surfaces by the fine aggregate. Macrotexture is generally provided in asphalt pavement by proper aggregate gradation and in surfaces by a supplemental treatment such as those listed in paragraph 7(a).

FHWA Hot Mix Asphalt Pavement Guidelines

e. From what references do the controls operate (fixed or moving)? Controls must be approved by the EIC. _____ FIXED (taut reference line at or near

STAR SEAL | MICRO-PAVE SEALERS

STAR MICRO-PAVE SUPREME® is a premium grade, Asphalt Emulsion (water based) sealcoating for jobs that demand only the best performance. STAR MICRO-PAVE SUPREME® has the industries highest degree of toughness and water repellency, unmatched by any competitive sealer.

Stone Mastic Asphalt - Civil Engineering

These are Dense Graded asphalt, Stone Mastic Asphalt and Open Graded Asphalt. Stone mastic asphalt (SMA) is a stone-on-stone like skeletal structure of gap graded aggregate, bonded together by mastic, which actually is higher binder content, filler and fiber to reduce the binder drain.

Pavement Design & Information

The Minnesota Department of Transportation provides its home page with links to its regional offices, bid letting, construction, future highway plans, hot topics, jobs, library, licensing information, map sales, news, public meetings, research, road & travel information, and related links.

Preventive Maintenance - Micro-Surfacing

Result . Viscosity, Saybolt Furol, 77 ºF (25 ºC), SFS 20-100 Storage Stability Test, 24 hours, % 1 max. Particle Charge Test Positive Sieve Test, No. 20 (850 µm), retained on sieve, % 0.10 max.

Micro-Surfacing – Martin Companies

The high-performance surface treatment is a mixture of fine dense-graded aggregate, polymer modified asphalt emulsion, water, mineral fillers and additives. The aggregate is 100% crushed, and meets stringent requirements for clay content, soundness and abrasion.

Standard Specifications for Highways and Structures | ddot

DDOT Standard Specifications for Highways and Structures - 2009 - This publication details the engineering specifications for highways and structures in the District of Columbia. A specification is an explicit set of requirements to be satisfied by a material, product, or service.

Existing Surface Preparation for Overlays - Pavement ...

Overlays (either structural or non-structural) make up a large portion of the roadway paving done today. The degree of surface …

AASHTO Emulsion Standards Updates | AsphaltPro Magazine ...

That’s why the Emulsion Task Force (ETF) was established in 2008, with support from the Federal Highway Administration, FP2 Inc., the National Center for Pavement Preservation, International Slurry Surfacing Association, Asphalt Emulsion Manufacturers Association and Asphalt Recycling and Reclaiming Association.